New cooktop or oven, gas hot water swap, BBQ point off the kitchen line, leak repair, or full gas rough-in for a renovation. Licensed gas work across natural gas and LPG for homes, hospitality kitchens, and industrial sites across Penrith and Western Sydney. NSW Plumbing licence 309265C, gas endorsement included.
Gas calls usually fall into one of four buckets. Quick read on what you’re dealing with so you know what to mention when you ring, and what we’ll need to bring.
Sulphur or rotten-egg smell indoors, near a meter, or by an appliance. Don’t light anything, don’t switch lights on or off, get outside. If you can do it safely, isolate the supply at the meter (natural gas) or shut the cylinder valves (LPG). Treat it as urgent until proven otherwise.
Replacing the cooktop, swapping a gas hot water unit, installing a heater, fitting a BBQ point. We connect, pressure-test, commission, and issue the compliance certificate.
Extending the line for a new BBQ point, roughing in a renovation, capping a line that’s no longer needed, or adding a new appliance run. The pipework itself, not just an appliance connection.
Every appliance install, line extension, or repair we carry out ends with a Gas Compliance Certificate. Required in NSW, kept on file, copy emailed to you.
Gas fitting in NSW covers everything from a single appliance connection to a full industrial gas system. Here’s how we break it down, and what each scope actually looks like on the day.
Cooktops, ovens, hot water units, gas heaters, BBQs, hospitality cooktops. Disconnect old, connect new, pressure-test, commission, issue the compliance paperwork.
New runs from the meter to a new appliance point, BBQ point off the kitchen, rough-in for a renovation, capping unused runs. Copper or approved poly to AS/NZS 5601, pressure-tested.
Confirmed smell, dropping meter reading, hissing at a fitting, or your distributor has flagged a problem. Pressure test the system, locate the leak, repair the affected section, re-test, certify.
Every appliance install, line extension, or repair we carry out ends with a Gas Compliance Certificate to AS/NZS 5601, issued for the work we performed.
A lot of Penrith’s housing stock was built in the 1960s, 70s and 80s, and the original gas runs were laid in copper at the same time. Most of it is still in service. Most of it is still fine. Some of it isn’t, and a renovation is when the difference shows up.
The other Penrith pattern: renovation waves. A kitchen reno usually means relocating the cooktop, adding a BBQ point, sometimes converting the hot water system. Each one is a small gas job in its own right, often booked around an existing builder’s schedule.
Where leaks tend to happen on older Penrith installs: at joints that have been disturbed during prior work, at appliance valves that weren’t designed for thirty years of cycling, and at meter regulators that are quietly past their service life.
For most domestic appliance jobs, this is the day. Line extensions and full rough-ins are longer, but the order is the same. Every job ends with a Gas Compliance Certificate where the scope qualifies.
You tell us the appliance or the scope, the gas type (natural or LPG), and what’s already there. A photo of the existing point and the appliance plate helps us quote accurately.
We confirm the connection point, check meter capacity for new loads, identify any compliance issues with the existing setup, and write a firm quote covering install and certification.
Source approved fittings, copper or poly to AS/NZS 5601. On the day we isolate at the meter, depressurise, and confirm zero pressure before any disconnection.
Connect the appliance or run the new line, then a soap-and-gauge pressure test to confirm no leaks. Commission the appliance, set burner pressure, run it through cycles.
Issue the Gas Compliance Certificate, walk you through isolation and shut-off, hand over the unit documentation. 12-month workmanship warranty kicks in. Invoice emailed through to you.
Gas isn’t water. A bad joint on a water line stains a ceiling. A bad joint on a gas line is a different conversation. We work to the standards every gas fitter is meant to, and we issue paperwork that proves it.
Direct answers from a licensed Penrith gas fitter. If your question isn’t here, send it through and we’ll add it.
Ring the workshop and tell us the scope. We’ll narrow the quote on the call and book the visit on the spot. Compliance certificate issued on every qualifying job.
